0
TECHNICAL PAPERS

Machining Quality and Cost: Estimation and Tradeoffs

[+] Author and Article Information
Panicos Nicolaou, Deborah L. Thurston, James V. Carnahan

Department of General Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801-2996

J. Manuf. Sci. Eng 124(4), 840-851 (Oct 23, 2002) (12 pages) doi:10.1115/1.1511169 History: Received March 01, 2000; Revised December 01, 2001; Online October 23, 2002
Copyright © 2002 by ASME
Your Session has timed out. Please sign back in to continue.

References

Chen, W., Wiecek, M., and Zhang, J., 1998, “Quality Utility-A Compromise Programming Approach to Robust Design,” Proc. ASME Design Automation Conference, Atlanta, Georgia.
Ashby, F., and Esawl, A., 1999, “Cost Estimating for Process Selection,” Proc. ASME Design for Manufacturing Conference, Las Vegas, Nevada.
Xirouchakis, P., and Kiritsis, D., 1998, “An Incremental Part Manufacturing Cost Estimation Algorithm Using Petri Nets,” Proc. ASME Design for Manufacturing Conference, Atlanta, Georgia.
Thornton, A., 1997, “Using Key Characteristics to Balance Cost and Quality During Product Development,” Proc. ASME Design Theory and Methodology Conference, Sacramento, California.
Wu,  C., Chen,  Z., and Tang,  C., 1998, “Component Tolerance Design for Minimum Quality Loss and Manufacturing Cost,” Computers in Industry, 35, pp. 223–232.
Cozzens,  D. A., Rao,  P. D., Olson,  W. W., Sutherland,  J. W., and Panetta,  J. M., 1999, “An Experimental Investigation into the Effect of Cutting Fluid Conditions on the Boring of Aluminum Alloys,” ASME J. Manuf. Sci. Eng., 121(3), pp. 434–439.
Locascio,  A., and Thurston,  D., 1998, “Transforming the House of Quality to a Multiobjective Optimization Formulation,” Struct. Optim., 16(2), pp. 136–146.
Urlichs, R., 1999, “A Predictive Quality Model in a Design for Machining Decision Tool with Consideration of Uncertainty,” Thesis, University of Illinois at Urbana-Champaign.
Walsh, R., 1999, McGraw-Hill Machining and Metalworking Handbook, McGraw-Hill, New York.
Surendran, V., 1998, “A Study of Hole Quality in Drilling,” Master’s thesis, University of Illinois at Urbana-Champaign.
Cooper,  R., and Kaplan,  R. S., 1991, “Profit Priorities from Activities Based Costing,” Harvard Bus. Rev., May–June, 130–135.
Schreiner, T., 1999, “Cost Estimation for Tradeoff Decisions in Design for Manufacturing,” Thesis, University of Illinois at Urbana-Champaign.
Bidanda,  B., Kadilal,  M., and Billo,  R. E., 1998, “Development of an Intelligent Castability and Cost Estimation System,” Int. J. Prod. Res., 36, pp. 547–568.
Kalpakjian, S., 1995, Manufacturing Engineering and Technology, Third Edition, Addison-Wesley.
Boothroyd, G., and Knight, W. A., 1989, Fundamentals of Machining and Machine Tools, 2nd edition.
Berry, M., 2000, “A Machining and Cutting Fluid Decision Tool for Cost, Quality and Environmental Tradeoffs,” Master’s thesis, University of Illinois at Urbana-Champaign.
Skerlos, S. J., DeVor, R. E., and S. G. Kapoor, 1998, “Environmentally Conscious Disposal Considerations in Cutting Fluid Selection,” IMEC-E-Proceedings of ASME.
Childers, J. C., 1994, “The Chemistry of Metalworking Fluids,” Metalworking Fluids, Marcel-Dekker, New York, pp. 165–189.
U.S. Environmental Protection Agency, 1983b, “Treatability Manual: Technology for Control/Removal of Pollutants,” Washington DC, Office of Research and Development, Publication No EPA-600/2-82-001c.
U.S. Environmental Protection Agency, 1983a, “Treatability Manual: Cost Estimating,” Washington DC, Office of Research and Development, Publication No EPA-600/2-82-001d.
U.S. Environmental Protection Agency, 1995, “Development Document for the Proposed Effluent Limitations Guidelines and Standards for the Metal Products and Machinery Phase I Source Category,” Springfield VA, U.S. Department of Commerce, Publication No 821-R-95-021.
Wright,  D. G., and Woods,  D. R., 1993, “Evaluation of Capital Cost Data. Part 7: Liquid Waste Disposal with Emphasis on Physical Treatment,” Can. J. Chem. Eng., 71, pp. 575–590.
Thurston,  D., and Tiefu,  Liu, 1991, “Design Evaluation of Multiple Attributes under Uncertainty,” Int. J. Syst. Autom.: Res. Appl., 1(2), pp. 143–159.
Thurston,  D. L., Carnahan,  J. V., and Liu,  T., 1994, “Optimization of Design Utility,” ASME J. Mech. Des., 116(3), pp. 801–808.
Thurston,  D. L., 2001, “Real and Perceived Limitations to Decision Based Design with Utility Analysis,” ASME J. Mech. Des., 123(2), pp. 176–182.
Tian,  Y. Q., Thurston,  D. L., and Carnahan,  J. V., 1994, “Incorporating End-users’ Attitudes Towards Uncertainty into an Expert System,” ASME J. Mech. Des., 116(2), pp. 493–500.
Thurston,  D., 1991, “A Formal Method for Subjective Design Evaluation with Multiple Attributes,” Res. Eng. Des., 3(2), pp. 105–122.
Keeney, R., and Raiffa, H., 1993, Decisions with Multiple Objectives, Cambridge University Press.

Tables

Errata

Discussions

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In